50W Dimmable LED Driver 350mA - 1050mA 1-10V / PUSH Dimming
| Place of Origin: | Zhejiang, China (Mainland) |
|
|
| Add to My Favorites | |
| HiSupplier Escrow |
Product Detail
50W Dimmable LED Driver 350mA - 1050mA 1-10V / PUSH Dim
50W Dimmable LED Driver 350mA - 1050mA 1-10V / PUSH Dimming
Description:
1, Stand-by power consumption is only 0.5W, save more energy.
2, No screws deign for housing, quick and easy installation can save more labor cost.
3, The driver has narrow strip structure, input and output located in the opposite end, it more easy to assemble and go through a small cut hole.
4, With non-flickering design, the driver supplies you a excellent lighting solution.
5, Multi-output current and voltage is suitable for different LED lights. Output current from 250mA to 700mA can be selected by DIP switches.
6, Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required.
7, Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores.
8, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.
9, Maximum length of the cable, from switch to last driver is 20m.
10, Factory setting: 100% dimming level and 350mA output.
11, Reset the LED diver easily by a jumper.
12, Press-in terminals in primary and secondary side, easy assembly.
13, Protection: Short circuit / Over voltage / Over temperature.
14, Long life span 50,000h, 5 years guaranty.
Applications:
For LED panel light, LED down light, led strip, led tube etc…
Dimming Operation:
A) PUSH Dim
Short push (<0.1sec): Ignore, to avoid reaction on AC spike.
Short push (0.1~1sec): Switch on or switch off.
Long push (>1sec): Dimming up or down, dimming level automatically stops at minimum or maximum value.
B) 1-10V Dim
Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.
Synchronization:
For the resynchronization to work correctly when more than one driver is connected to the same push button, follow steps of below after the drivers are connected:
A) Press push button for more than one second, followed by a short push (<1s), now, led light switches off.
B) Do a long push, the system will be resynchronized.
Specifications
|
INPUT
|
Input voltage |
220-240Vac |
|
Input frequency |
50-60Hz |
|
|
Input current |
0.26A max |
|
|
Power factor |
≥0.90 |
|
|
Stand-by power |
0.5W max. |
|
|
Efficiency(Note1) |
≥87% |
|
|
Leakage current |
0.5mA/240Vac |
|
|
OUTPUT
|
Output current/voltage and load |
350mA 3-60V DC 21W max 500mA 3-60V DC 30W max 550mA 3-60V DC 33W max 650mA 3-58V DC 41W max 700mA 3-58V DC 41W max 750mA 3-56V DC 43W max 850mA 3-56V DC 47W max 900mA 3-56V DC 50W max 1050mA 3-48V DC 50W max |
|
China LED Driver Marketplace [China (Mainland)]
Business Type:Manufacturer |
